ДМИТРИЙ1973

Тогда есть такой вариант научится пользоваться кнопкой WWW.Только скрипты старта и отключения соеденения надо переписать названия по русски.И сразу им будет видно куда нажимать.У вас какая прошивка ,если 0.6.1,то киньте мне код в личку.И я вам перепишу как надо.А то у меня еще 0.6.0

Вообще то никакого,вот если на флешку с енигмой-то да.Но у меня не получилось.

д.Федор,как прикрутить выполнения своих команд при старте автоматом.Как не пытался в папке init.d свое поставить-не получается. Для примера делал так 3.start.sh-код /var/bin/свой скрипт

Да я все проверял,вижу что все работает.Вопрос в другом -это мешать не будет,все таки лишняя команда при старте.Короче нагрузка на рес.

д.Федор вопросик, если в pgi.conf оставить PPPD_PEER="gprs" USB_MODEM="12d1:1001" А сам модем не подключен и интернет идет по лану,как это будет влиять на работу тюнера .Или надо поменять в pgi.conf на none?Я это к тому,чтоб лишний раз настройки не менять.Конечно можно нажатием кнопки сделать замену,но хочется знать в принципе.

попробуй в начале первый вариант,только я думаю устройство надо использовать USB0 это я -Mihanism(в личку тебе написать не могу,почисти ящик)

Проверил ради интереса,открылся в KMPlayer

Как раз думал,что надо прошивку обновить :rolleyes:

AlBad-в топку NLB.Ставьте ПГИ и мы вам поможем,а скорей всего все просто заработает как надо.

Заработал модем E1550 pgi.conf PPPD_PEER="gprs" USB_MODEM="12d1:1001" моя конфигурация gprs,здесь раскоментировал и прописал вот такие строчки,остальное стандартно user wap password wap /dev/ttyUSB0 460800 gprs.chat 'OK' 'AT+CGDCONT=1,"IP","internet.tele2.lv","",0,0' 'OK' 'ATDT*99#' 'CONNECT' '' Ошибка была вот в чем,два дня возился сеть не устанавливалась.Сегодня взял усб удлинитель,убрал модем подальше от антенны и все заработало.Одно но, когда пытаюсь запустить сеть в ручную,через скрипт scrplg-ppp-connect-start.sh ,то если сеть взялась(у меня почему то со второго раза получается) из плагина скриптов не выйти.Приходится вырубать двумя кнопками на тюнере. Спасибо все за помощь,отдельно д.Федору за эту фичу(с меня причитается :rolleyes: )

тогда пару вопросов- у меня симка для сотовика ,user и password -wap Получается в файле gprs раскоментировать и прописать user wap А в файле(тюнера под рукой нет)где пароль,так * * "wap"*

все понял-спасибо.Вечером снова в бой :rolleyes:

Так я уже раз так двести попробовал :rolleyes: как еще?конкретно напишите.Просто в том,что я понимаю в тюнере,я не кому не отказываю в помощи.Хотя мог бы и промолчать-типа сам ковыряй.

может вы знаете -что значит убрал APN?И почему некоторые пишут ,что допустим как у меня- internet.tele2.lv,прописывать не надо?

тогда обьясните для чайника что это значит- ваша цитата Вот как выглядит gprs.chat. Убрал APN, после этого у меня появилась связь 'OK' 'AT&f+cgdcont=1,"IP","","",0,0' 'OK' 'ATDT*99#' как мне делать?Написано в самой программе на компе для модема в свойствах , как раз APN,internet.tele2.lv Уже голова пухнет возится.

когда я делаю так 'OK' 'OK' 'AT&f+cgdcont=1,"IP","internet.tele2.lv","",0,0' 'OK' 'ATDT*99#' 'CONNECT' '' у меня пишет [PGI ~]$ pppd call gprs & [PGI ~]$ Script /sbin/chat -v -f /var/etc/ppp/chats/gprs.chat finished (pid 1148), status = 0x3 Connect script failed если так 'OK' 'AT+CGDCONT=1,"IP","internet.tele2.lv","",0,0' 'OK' 'ATDT*99#' 'CONNECT' '' то пост №231 вот команда dmesg ata1: SATA max UDMA/133 cmd 0xB9209000 ctl 0xB9209820 bmdma 0x0 irq 170ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:746b 83:7f69 84:6123 85:7469 86:bc41 87:6123 88:407f ata1: dev 0 ATA-8, max UDMA/133, 625142448 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_stm Vendor: ATA Model: SAMSUNG HM320II Rev: 2AC1 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda Generic ST boards onboard flash device: 0x02000000 (32.0MB) at 0x00000000 drivers/mtd/maps/cuberevo-mini.c init_stboards[217] onboard_map.virt = 0xa0000000 Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 Onboard_Flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 9 MTD partitions on "Onboard_Flash": 0x00000000-0x00040000 : "nor.boot" 0x00040000-0x00060000 : "nor.config_welcome" 0x00060000-0x00260000 : "nor.kernel" 0x00260000-0x01600000 : "nor.root" 0x01600000-0x02000000 : "nor.db" 0x00060000-0x01600000 : "nor.kernel_root" 0x00060000-0x02000000 : "nor.kernel_root_db" 0x00040000-0x02000000 : "nor.all_noboot" 0x00000000-0x02000000 : "nor.all" usbmon: debugfs is not available ST40_start_host_control ST40_start_host_control proceeding ST40-ehci ST40-ehci.2: ST EHCI Host Controller ST40-ehci ST40-ehci.2: new USB bus registered, assigned bus number 1 ST40-ehci ST40-ehci.2: irq 169, io mem 0xb91ffe00 ST40-ehci ST40-ehci.2: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (ST40) ST40_start_host_control ST40-ohci ST40-ohci.1: STB7100 OHCI ST40-ohci ST40-ohci.1: new USB bus registered, assigned bus number 2 ST40-ohci ST40-ohci.1: irq 168, io mem 0xb91ffc00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usb 1-1: new high speed USB device using ST40-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usbcore: registered new driver asix usbcore: registered new driver net1080 usbcore: registered new driver plusb i2c /dev entries driver i2c_st40_pio: ST40 PIO based I2C Driver i2c_st40_pio: allocated pin (2,0) for scl (0x847a7c0c) i2c_st40_pio: allocated pin (2,1) for sda (0x847a7c1c) i2c_st40_pio: allocated pin (3,0) for scl (0x847a7c8c) i2c_st40_pio: allocated pin (3,2) for sda (0x847a7cac) i2c_st40_pio: allocated pin (4,0) for scl (0x847a7d0c) i2c_st40_pio: allocated pin (4,1) for sda (0x847a7d1c) i2c_st40_pio bus 0: SCL=PIO2[0], SDA=PIO2[1] i2c_st40_pio bus 1: SCL=PIO3[0], SDA=PIO3[2] i2c_st40_pio bus 2: SCL=PIO4[0], SDA=PIO4[1] STMicroelectronics - Coprocessors st231 Init st-coprocessor-0: No RAM reserved st231-0 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- st-coprocessor-1: No RAM reserved st231-1 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- ip_conntrack version 2.4 (648 buckets, 5184 max) - 224 bytes per conntrack ip_conntrack_pptp version 3.1 loaded ip_nat_pptp version 3.0 loaded '; CODE и еще вопрос,что в это время должно быть в айпи настройках тюнера.Дело в том что мне надо по телнету через комп заходить,чтоб команды давать по настройке

я запутался какое устройство правильное /dev/ttyUSB0 или /dev/ttyUSB2 В сообщении выше /dev/ttyUSB2 а вот лог с /dev/ttyUSB0 Welcome to Cuberevocuberevo login: root Password: [PGI ~]$ pppd call gprs & [PGI ~]$ Script /sbin/chat -v -f /var/etc/ppp/chats/gprs.chat finished (pid 1145), status = 0x0 Serial connection established. using channel 1 Using interface ppp0 Connect: ppp0 <--> /dev/ttyUSB0 sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x77cc7e5e> <pcomp> <accomp>] rcvd [LCP ConfReq id=0x0 <asyncmap 0x0> <auth chap MD5> <magic 0xfa84ce> <pcomp> <accomp>] sent [LCP ConfAck id=0x0 <asyncmap 0x0> <auth chap MD5> <magic 0xfa84ce> <pcomp> <accomp>] rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x77cc7e5e> <pcomp> <accomp>] rcvd [LCP DiscReq id=0x1 magic=0xfa84ce] rcvd [CHAP Challenge id=0x1 <508c9b49f0fd1883ccdac7ddd4f8ed6b>, name = "UMTS_CHAP_SRVR"] Warning - secret file /etc/ppp/chap-secrets has world and/or group access sent [CHAP Response id=0x1 <b3e29556b0f5e5657c06458952638e2b>, name = "cuberevo"] rcvd [CHAP Success id=0x1 ""] CHAP authentication succeeded CHAP authentication succeeded sent [iPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>] rcvd [iPCP ConfNak id=0x1 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x2 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x2 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x3 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x3 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x4 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x4 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x5 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x5 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x6 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x6 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x7 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x7 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x8 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x8 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x9 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x9 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0xa <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0xa <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0xb <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0xb <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0xc <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0xc <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0xd <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0xd <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0xe <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0xe <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0xf <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0xf <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x10 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x10 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x11 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x11 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x12 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x12 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x13 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x13 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x14 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x14 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x15 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x15 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x16 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x16 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x17 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x17 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x18 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x18 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x19 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x19 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x1a <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x1a <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x1b <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x1b <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x1c <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x1c <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x1d <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x1d <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x1e <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x1e <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x1f <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x1f <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x20 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x20 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x21 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x21 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x22 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x22 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x23 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] rcvd [iPCP ConfNak id=0x23 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] sent [iPCP ConfReq id=0x24 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>] IPCP: timeout sending Config-Requests sent [LCP TermReq id=0x2 "No network protocols running"] sent [LCP TermReq id=0x3 "No network protocols running"] Connection terminated. Modem hangup '; CODE

что означают эти строчки [PGI ~]$ pppd call gprs &[PGI ~]$ Script /sbin/chat -v -f /var/etc/ppp/chats/gprs.chat finished (pid 1143), status = 0x0 Serial connection established. using channel 1 Using interface ppp0 Connect: ppp0 <--> /dev/ttyUSB2 Warning - secret file /etc/ppp/pap-secrets has world and/or group access sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc095ec96> <pcomp> <accomp>] LCP: timeout sending Config-Requests Connection terminated. Receive serial link is not 8-bit clean: Problem: all had bit 7 set to 0 Modem hangup '; CODE

Все должно работать,если только мультибут не правили на этих кнопках.

скиньте плиз все настройки для модема мне в личку. Народ писал-эму перезапустить попробовать.

У меня с этим скином такая же хрень была,я думаю ошибка в названии Verde Reliz,в два слова с пробелом нельзя. Победил так,при старте надо нажать кнопку 8 или 9(точно не помню,с работы пишу).В редми описана процедура приостановки загрузки.И можно все заменить,д.Федору спасибо за эту фичу.

что означает этот лог? [1.usbmodem] [07:51:23] started [1.usbmodem] [07:51:23] USB_MODEM is set to 12d1:1001 [1.usbmodem] [07:51:28] scanning usb connected devices 12d1:1001 [1.usbmodem] [07:51:32] device directly matching 12d1:1001 is connected [1.usbmodem] [07:51:32] loading usbserial.ko for vendor=0x12d1 product=0x1001 [1.usbmodem] [07:51:32] pppd peer is set to: gprs [1.usbmodem] [07:51:33] detecting serial device in /dev, attempt #1/10 [1.usbmodem] [07:51:33] starting PPP daemon using peer: gprs [1.usbmodem] [07:51:34] finished [PGI ~]$ ls -ls /dev/tty* 0 crw-rw-rw- 1 root root 5, 0 Dec 10 2027 /dev/tty 0 crw-rw---- 1 root root 204, 40 Dec 10 2027 /dev/ttyAS0 0 crw-rw---- 1 root root 204, 41 Dec 10 2027 /dev/ttyAS1 0 crw-rw---- 1 root root 188, 0 Apr 12 07:42 /dev/ttyUSB0 0 crw-rw---- 1 root root 188, 1 Apr 12 07:42 /dev/ttyUSB1 0 crw-rw---- 1 root root 188, 2 Apr 12 07:42 /dev/ttyUSB2 И подскажите плиз что прописывать в файлах,вот с такими параметрами У меня так 3G tele2 APN:data.tele2.lv

Взгляните кто понимает-что я натворил CODE _linenums:0'><div class='codetop'>CODE sata_stm using hardware scatter/gather sata_stm SATA version 1.00 DMA version 2.02 ata1: SATA max UDMA/133 cmd 0xB9209000 ctl 0xB9209820 bmdma 0x0 irq 170 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:746b 83:7f69 84:6123 85:7469 86:bc41 87:6123 88:007f ata1: dev 0 ATA-8, max UDMA/133, 625142448 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_stm Vendor: ATA Model: SAMSUNG HM320II Rev: 2AC1 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda Generic ST boards onboard flash device: 0x02000000 (32.0MB) at 0x00000000 drivers/mtd/maps/cuberevo-mini.c init_stboards[217] onboard_map.virt = 0xa0000000 Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 Onboard_Flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 9 MTD partitions on "Onboard_Flash": 0x00000000-0x00040000 : "nor.boot" 0x00040000-0x00060000 : "nor.config_welcome" 0x00060000-0x00260000 : "nor.kernel" 0x00260000-0x01600000 : "nor.root" 0x01600000-0x02000000 : "nor.db" 0x00060000-0x01600000 : "nor.kernel_root" 0x00060000-0x02000000 : "nor.kernel_root_db" 0x00040000-0x02000000 : "nor.all_noboot" 0x00000000-0x02000000 : "nor.all" usbmon: debugfs is not available ST40_start_host_control ST40_start_host_control proceeding ST40-ehci ST40-ehci.2: ST EHCI Host Controller ST40-ehci ST40-ehci.2: new USB bus registered, assigned bus number 1 ST40-ehci ST40-ehci.2: irq 169, io mem 0xb91ffe00 ST40-ehci ST40-ehci.2: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (ST40) ST40_start_host_control ST40-ohci ST40-ohci.1: STB7100 OHCI ST40-ohci ST40-ohci.1: new USB bus registered, assigned bus number 2 ST40-ohci ST40-ohci.1: irq 168, io mem 0xb91ffc00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usb 1-1: new high speed USB device using ST40-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usbcore: registered new driver asix usbcore: registered new driver net1080 usbcore: registered new driver plusb i2c /dev entries driver i2c_st40_pio: ST40 PIO based I2C Driver i2c_st40_pio: allocated pin (2,0) for scl (0x847a7c0c) i2c_st40_pio: allocated pin (2,1) for sda (0x847a7c1c) i2c_st40_pio: allocated pin (3,0) for scl (0x847a7c8c) i2c_st40_pio: allocated pin (3,2) for sda (0x847a7cac) i2c_st40_pio: allocated pin (4,0) for scl (0x847a7d0c) i2c_st40_pio: allocated pin (4,1) for sda (0x847a7d1c) i2c_st40_pio bus 0: SCL=PIO2[0], SDA=PIO2[1] i2c_st40_pio bus 1: SCL=PIO3[0], SDA=PIO3[2] i2c_st40_pio bus 2: SCL=PIO4[0], SDA=PIO4[1] STMicroelectronics - Coprocessors st231 Init st-coprocessor-0: No RAM reserved st231-0 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- st-coprocessor-1: No RAM reserved st231-1 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- ip_conntrack version 2.4 (648 buckets, 5184 max) - 224 bytes per conntrack ip_conntrack_pptp version 3.1 loaded ip_nat_pptp version 3.0 loaded ip_tables: © 2000-2006 Netfilter Core Team ipt_recent v0.3.1: Stephen Frost <[email protected]>. http://snowman.net/projects/ipt_recent/ TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ieee80211: 802.11 data/management/control stack, git-1.1.7 ieee80211: Copyright © 2004-2005 Intel Corporation <[email protected]> ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' stmmac_open: MAC address 00:13:18:00:00:e2 VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 96k freed Warning: unable to open an initial console. Empty flash at 0x0004fffc ends at 0x00050000 CLEANMARKER node found at 0x00050000, not first node in block (0x00040000) Empty flash at 0x0006fffc ends at 0x00070000 CLEANMARKER node found at 0x00070000, not first node in block (0x00060000) Empty flash at 0x0010fffc ends at 0x00110000 CLEANMARKER node found at 0x00110000, not first node in block (0x00100000) Empty flash at 0x0014fffc ends at 0x00150000 CLEANMARKER node found at 0x00150000, not first node in block (0x00140000) Empty flash at 0x0016fffc ends at 0x00170000 CLEANMARKER node found at 0x00170000, not first node in block (0x00160000) Empty flash at 0x001afffc ends at 0x001b0000 CLEANMARKER node found at 0x001b0000, not first node in block (0x001a0000) CLEANMARKER node found at 0x002d0000, not first node in block (0x002c0000) input: Relook IR Keyboard as /class/input/input0 ciio: module license 'unspecified' taints kernel. ciio device driver. ciio client i2c is attached stos_core: no version magic, tainting kernel. stos_core_init_module(): Initializing STOS Module stcommon_core: no version magic, tainting kernel. stcommon_core_init_module(): Initializing STCOMMON Module Setting all Group priorities done PTI Clock: Cut 3.0 detected -> applying 27000000Hz oscillator config ... Preproc Clock: Cut 3.0 detected -> setting Preproc clock. mod_lxload_init: Initializing LXLOAD kernel Module, StartAddress: 0x04200000 LXLOADER virtual io kernel address of phys 0xa4200000 = 0xa4200000 lxload_open: major=254 minor=0 setting up Audio LX in NON-DEBUG mode lxload_release: major=254 minor=0 Starting Audio LX by disabling reset LX loaded: Base: 0xa4200000 Last: 0xa42cab04 Size:830212 mod_lxload_exit: Exiting LXLOAD kernel Module stmmac_open: MAC address 00:13:18:00:00:e2 mod_lxload_init: Initializing LXLOAD kernel Module, StartAddress: 0x04000000 LXLOADER virtual io kernel address of phys 0xa4000000 = 0xa4000000 lxload_open: major=254 minor=0 setting up LX in NON-DEBUG mode lxload_release: major=254 minor=0 Starting video LX by disabling reset LX loaded: Base: 0xa4000000 Last: 0xa4093d9c Size:605596 mod_lxload_exit: Exiting LXLOAD kernel Module PHY: 0:01 - Link is Up - 100/Full Adding 1004020k swap on /dev/sda1. Priority:-1 extents:1 across:1004020k EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended stapi: no version magic, tainting kernel. stblit_ioctl_init_module: Initializing STBLIT IOCTL Module Load module stclkrv_core by modprobe (pid 743) stvmix_ioctl_init_module: Initializing STVMIX IOCTL Module Load module stavmem_ioctl [248] by modprobe (pid 743) stpio_core_init_module(): Initializing STPIO Module stvout_ioctl_init_module: Initializing STVOUT IOCTL Module Load module stfdma_ioctl [243] by modprobe (pid 743) Load module fdma [242] by modprobe (pid 743) stvtg_ioctl_init_module: Initializing STVTG IOCTL Module Load module stpti4_core by modprobe (pid 743) Load module staudlx_core [237] by modprobe (pid 743) sthdmi_ioctl_init_module: Initializing STHDMI IOCTL Module utils_ioctl_init_module: Initializing UTILS IOCTL Module usbserial: no version magic, tainting kernel. usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbserial_generic 1-1:1.0: generic converter detected usb 1-1: generic converter now attached to ttyUSB0 usbserial_generic 1-1:1.1: generic converter detected usb 1-1: generic converter now attached to ttyUSB1 usbserial_generic 1-1:1.2: generic converter detected usb 1-1: generic converter now attached to ttyUSB2 usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core ACCESS 00000002 Open Read/Write stevt: Setting New buffer Size 102400 ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write UTILS: ioctl command 0 [0x00007e00] ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write Fixing up unaligned userspace access in "sbox" pid=938 pc=0x0047249c ins=0x6141 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x004724ac ins=0x2411 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x0047249c ins=0x6141 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x004724ac ins=0x2411 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x0047249c ins=0x6141 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x004724ac ins=0x2411 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x0047249c ins=0x6141 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x004724ac ins=0x2411 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x297add4e ins=0x6101 Fixing up unaligned userspace access in "sbox" pid=938 pc=0x297add5a ins=0x2011 REAP:+B -STC=3109301912 PTS=3109444231, Drift=142319 Th=1890, NumberToDo=80 REAP:+P -STC=3113911720 PTS=3113928031, Drift=16311 Th=1890, NumberToDo=10 REAP:+I -STC=2729019328 PTS=2729087835, Drift=68507 Th=1890, NumberToDo=38 PCMPLAYER(PCMPLAYER0) => Pause (ms)=24 PCMPLAYER(PCMPLAYER0) => Pause (ms)=14 [PGI ~]$ Т ';

это первая команда [PGI ~]$ lsusb Bus 002 Device 001: ID 0000:0000 Bus 001 Device 002: ID 12d1:1446 Huawei Technologies Co., Ltd. Bus 001 Device 001: ID 0000:0000 потом в пги конфиге,прописал PPPD_PEER="gprs" USB_MODEM="12d1:1446" после перезагрузки [PGI ~]$ lsusb Bus 002 Device 001: ID 0000:0000 Bus 001 Device 002: ID 12d1:1001 Huawei Technologies Co., Ltd. E620 USB Modem Bus 001 Device 001: ID 0000:0000 Я очень далек от этого,но понимаю что надо отключить SD-ROM,но не получается CODE _linenums:0'><div class='codetop'>CODE libata version 1.20 loaded. sata_stm version 0.3 sata_stm using hardware scatter/gather sata_stm SATA version 1.00 DMA version 2.02 ata1: SATA max UDMA/133 cmd 0xB9209000 ctl 0xB9209820 bmdma 0x0 irq 170 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:746b 83:7f69 84:6123 85:7469 86:bc41 87:6123 88:407f ata1: dev 0 ATA-8, max UDMA/133, 625142448 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_stm Vendor: ATA Model: SAMSUNG HM320II Rev: 2AC1 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda Generic ST boards onboard flash device: 0x02000000 (32.0MB) at 0x00000000 drivers/mtd/maps/cuberevo-mini.c init_stboards[217] onboard_map.virt = 0xa0000000 Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 Onboard_Flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 9 MTD partitions on "Onboard_Flash": 0x00000000-0x00040000 : "nor.boot" 0x00040000-0x00060000 : "nor.config_welcome" 0x00060000-0x00260000 : "nor.kernel" 0x00260000-0x01600000 : "nor.root" 0x01600000-0x02000000 : "nor.db" 0x00060000-0x01600000 : "nor.kernel_root" 0x00060000-0x02000000 : "nor.kernel_root_db" 0x00040000-0x02000000 : "nor.all_noboot" 0x00000000-0x02000000 : "nor.all" usbmon: debugfs is not available ST40_start_host_control ST40_start_host_control proceeding ST40-ehci ST40-ehci.2: ST EHCI Host Controller ST40-ehci ST40-ehci.2: new USB bus registered, assigned bus number 1 ST40-ehci ST40-ehci.2: irq 169, io mem 0xb91ffe00 ST40-ehci ST40-ehci.2: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (ST40) ST40_start_host_control ST40-ohci ST40-ohci.1: STB7100 OHCI ST40-ohci ST40-ohci.1: new USB bus registered, assigned bus number 2 ST40-ohci ST40-ohci.1: irq 168, io mem 0xb91ffc00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usb 1-1: new high speed USB device using ST40-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice scsi1 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning scsi2 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usbcore: registered new driver asix usbcore: registered new driver net1080 usbcore: registered new driver plusb i2c /dev entries driver i2c_st40_pio: ST40 PIO based I2C Driver i2c_st40_pio: allocated pin (2,0) for scl (0x847a7c0c) i2c_st40_pio: allocated pin (2,1) for sda (0x847a7c1c) i2c_st40_pio: allocated pin (3,0) for scl (0x847a7c8c) i2c_st40_pio: allocated pin (3,2) for sda (0x847a7cac) i2c_st40_pio: allocated pin (4,0) for scl (0x847a7d0c) i2c_st40_pio: allocated pin (4,1) for sda (0x847a7d1c) i2c_st40_pio bus 0: SCL=PIO2[0], SDA=PIO2[1] i2c_st40_pio bus 1: SCL=PIO3[0], SDA=PIO3[2] i2c_st40_pio bus 2: SCL=PIO4[0], SDA=PIO4[1] STMicroelectronics - Coprocessors st231 Init st-coprocessor-0: No RAM reserved st231-0 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- st-coprocessor-1: No RAM reserved st231-1 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- ip_conntrack version 2.4 (648 buckets, 5184 max) - 224 bytes per conntrack ip_conntrack_pptp version 3.1 loaded ip_nat_pptp version 3.0 loaded ip_tables: © 2000-2006 Netfilter Core Team ipt_recent v0.3.1: Stephen Frost <[email protected]>. http://snowman.net/projects/ipt_recent/ TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ieee80211: 802.11 data/management/control stack, git-1.1.7 ieee80211: Copyright © 2004-2005 Intel Corporation <[email protected]> ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' stmmac_open: MAC address 00:13:18:00:00:e2 VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 96k freed Warning: unable to open an initial console. Empty flash at 0x0004fffc ends at 0x00050000 CLEANMARKER node found at 0x00050000, not first node in block (0x00040000) Empty flash at 0x0006fffc ends at 0x00070000 CLEANMARKER node found at 0x00070000, not first node in block (0x00060000) Empty flash at 0x0010fffc ends at 0x00110000 CLEANMARKER node found at 0x00110000, not first node in block (0x00100000) Empty flash at 0x0014fffc ends at 0x00150000 CLEANMARKER node found at 0x00150000, not first node in block (0x00140000) Empty flash at 0x0016fffc ends at 0x00170000 CLEANMARKER node found at 0x00170000, not first node in block (0x00160000) Empty flash at 0x001afffc ends at 0x001b0000 CLEANMARKER node found at 0x001b0000, not first node in block (0x001a0000) CLEANMARKER node found at 0x002d0000, not first node in block (0x002c0000) Empty flash at 0x0030ff60 ends at 0x00310000 CLEANMARKER node found at 0x00310000, not first node in block (0x00300000) Vendor: HUAWEI Model: Mass S<5> Vendor: HUAWEI Model: MMC Storage Rev: 2.31 Type: Direct-Access ANSI SCSI revision: 02 torage Rev: 2.31 Type: CD-ROM ANSI SCSI revision: 02 usb-storage: device scan complete sd 2:0:0:0: Attached scsi removable disk sdb usb-storage: device scan complete input: Relook IR Keyboard as /class/input/input0 ciio: module license 'unspecified' taints kernel. ciio device driver. ciio client i2c is attached stos_core: no version magic, tainting kernel. stos_core_init_module(): Initializing STOS Module stcommon_core: no version magic, tainting kernel. stcommon_core_init_module(): Initializing STCOMMON Module Setting all Group priorities done PTI Clock: Cut 3.0 detected -> applying 27000000Hz oscillator config ... Preproc Clock: Cut 3.0 detected -> setting Preproc clock. mod_lxload_init: Initializing LXLOAD kernel Module, StartAddress: 0x04200000 LXLOADER virtual io kernel address of phys 0xa4200000 = 0xa4200000 lxload_open: major=254 minor=0 setting up Audio LX in NON-DEBUG mode stmmac_open: MAC address 00:13:18:00:00:e2 lxload_release: major=254 minor=0 Starting Audio LX by disabling reset LX loaded: Base: 0xa4200000 Last: 0xa42cab04 Size:830212 mod_lxload_exit: Exiting LXLOAD kernel Module mod_lxload_init: Initializing LXLOAD kernel Module, StartAddress: 0x04000000 LXLOADER virtual io kernel address of phys 0xa4000000 = 0xa4000000 lxload_open: major=254 minor=0 setting up LX in NON-DEBUG mode lxload_release: major=254 minor=0 Starting video LX by disabling reset LX loaded: Base: 0xa4000000 Last: 0xa4093d9c Size:605596 mod_lxload_exit: Exiting LXLOAD kernel Module PHY: 0:01 - Link is Up - 100/Full Adding 1004020k swap on /dev/sda1. Priority:-1 extents:1 across:1004020k EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended stapi: no version magic, tainting kernel. stblit_ioctl_init_module: Initializing STBLIT IOCTL Module Load module stclkrv_core by modprobe (pid 782) stvmix_ioctl_init_module: Initializing STVMIX IOCTL Module Load module stavmem_ioctl [248] by modprobe (pid 782) stpio_core_init_module(): Initializing STPIO Module stvout_ioctl_init_module: Initializing STVOUT IOCTL Module Load module stfdma_ioctl [243] by modprobe (pid 782) Load module fdma [242] by modprobe (pid 782) stvtg_ioctl_init_module: Initializing STVTG IOCTL Module Load module stpti4_core by modprobe (pid 782) Load module staudlx_core [237] by modprobe (pid 782) sthdmi_ioctl_init_module: Initializing STHDMI IOCTL Module utils_ioctl_init_module: Initializing UTILS IOCTL Module ACCESS 00000002 Open Read/Write stevt: Setting New buffer Size 102400 ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write UTILS: ioctl command 0 [0x00007e00] ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write ACCESS 00000002 Open Read/Write Fixing up unaligned userspace access in "sbox" pid=976 pc=0x0047249c ins=0x6141 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x004724ac ins=0x2411 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x0047249c ins=0x6141 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x004724ac ins=0x2411 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x0047249c ins=0x6141 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x004724ac ins=0x2411 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x0047249c ins=0x6141 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x004724ac ins=0x2411 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x297add4e ins=0x6101 Fixing up unaligned userspace access in "sbox" pid=976 pc=0x297add5a ins=0x2011 REAP:+I -STC=2584458810 PTS=2584515667, Drift=56857 Th=1890, NumberToDo=32 PCMPLAYER(PCMPLAYER0) => Pause (ms)=13 [PGI ~]$';

вот лог при старте [1.usbmodem] [21:18:05] started [1.usbmodem] [21:18:05] USB_MODEM is set to 12d1:1446 [1.usbmodem] [21:18:11] scanning usb connected devices [1.usbmodem] [21:18:15] device directly matching 12d1:1446 is not found [1.usbmodem] [21:18:15] checking if 12d1:1446 is a usb_modeswitch'ed device [1.usbmodem] [21:18:16] finished checking usb_modeswitch files [1.usbmodem] [21:18:16] pppd peer is set to: gprs [1.usbmodem] [21:18:17] detecting serial device in /dev, attempt #1/10 [1.usbmodem] [21:18:19] detecting serial device in /dev, attempt #2/10 [1.usbmodem] [21:18:20] detecting serial device in /dev, attempt #3/10 [1.usbmodem] [21:18:20] detecting serial device in /dev, attempt #4/10 [1.usbmodem] [21:18:21] detecting serial device in /dev, attempt #5/10 [1.usbmodem] [21:18:22] detecting serial device in /dev, attempt #6/10 [1.usbmodem] [21:18:23] detecting serial device in /dev, attempt #7/10 [1.usbmodem] [21:18:25] detecting serial device in /dev, attempt #8/10 [1.usbmodem] [21:18:26] detecting serial device in /dev, attempt #9/10 [1.usbmodem] [21:18:27] detecting serial device in /dev, attempt #10/10 [1.usbmodem] [21:18:27] warning: could not detect any serial interfaces [1.usbmodem] [21:18:27] finished /sbin/pppd: In file /etc/ppp/peers/gprs: unrecognized option '/dev/ttyUSB0'