Здравствуйте не могу настроить sezam 900hd + AnyData adu-310a! (cdma-evdo)
при наборе gprs
[PGI ~]$ pppd call gprs &
[PGI ~]$ Script /sbin/chat -v -f /var/etc/ppp/chats/gprs.chat finished (pid 903
, status = 0x5
Connect script failed
при наборе 3g
в телнете
[PGI ~]$ pppd call 3g
[PGI ~]$
скриптом
ifconfing: ppp0: error fetcing interface information: device not found
pgi. conf
#############################################################################
# This is main configuration file for the PGI image
# The detailed explanation of each parameter is in the README files
#############################################################################
BACKUP_DIR="/media/pgi-backup"
CI_INIT="no"
CRON="no"
EPG_DATA_DIR="/media"
ETH_ADDR_LOW="none"
MEDIA_CLEAN="no"
NFSD="no"
NFS_REC="no"
NFS_REC_PROTO="tcp"
NTP_SYNC="no"
PPPD_PEER="gprs"
SAMBA="no"
SKIN="default"
USB_MODEM="16d5:6501"
WEBTV="no"
DEBUG="no"
3g.chat
ABORT BUSY
ABORT 'NO CARRIER'
ABORT ERROR
REPORT CONNECT
TIMEOUT 120
"" "AT&F"
OK "ATE1"
# Is there a PIN set on the SIM?
#OK "AT+CPIN?"
# What network are we connected to?
OK "AT+COPS?"
# Next line can be used to get a full list of available
# networks, but it takes a long time!
#OK "AT+COPS=?"
# List what AT commands we can issue to this card.
#OK "AT&V"
# Prefer UMTS networks over GPRS networks
# (but connect to GPRS if UMTS unavailable)
OK "AT_OPSYS=3"
# Current network signal strength
OK "AT+CSQ"
# Note the single quotes at the beginning and end,
# reversing the quoting (double at ends, single
# inside) does NOT work!
OK 'AT+CGDCONT=1,"IP",""'
TIMEOUT 60
OK "ATD#777"
CONNECT c
gprs.chat
# GPRS Chat File, contains all parameters that /usr/sbin/chat will pass to the modem to create the GPRS connection
#
#
# Abort Strings
'ABORT' 'BUSY'
'ABORT' 'ERROR'
'ABORT' 'NO ANSWER'
'ABORT' 'NO CARRIER'
'ABORT' 'NO DIALTONE'
'ABORT' 'Invalid Login'
'ABORT' 'Login incorrect'
'TIMEOUT' '10'
#
# Modem Init
'' 'ATZ'
#
#
'OK' 'ATM1L1'
#
# "internet" represents Vodafone's APN, whereas "general.t-mobile.uk" is T-mobiles UK APN address
'OK' 'AT&f+cgdcont=1,"IP","","",0,0'
'OK' 'ATDT#777'
'CONNECT' ''
peers - 3g
# If pppd reports this as a non-modem thing, then run the huaweiAktBbo program
/dev/ttyUSB0
#Baudrate -- Note that setting this to 384000 yields an error message
# about this speed not being supported!
115200
#Idle time for closing connection
idle 7200
#Lock the device for this PPPD process use only
lock
#Use normal handshaking
crtscts
#Assume it is a modem device and force modem control methods
modem
#Any user can start the connection
noauth
#Make the ppp link the default root
defaultroute
#Username and Password for computer/GlobeTrotter ppp link
#Normally ignored. Change if GSM Operator requires it
user mobile
password internet
#Change the path to chat if required for your version of Linux
connect "/sbin/chat -V -f /var/etc/ppp/3g.chat"
#Accept IP address provided by network
noipdefault
#Detach PPPD from console used to run the program {optional}
#updetach
#Get DNS addresses from operator
usepeerdns
#Don't use VJ compression for ppp link
novj
# Make the connection persistent, and not terminate if/when errors occur.
persist
maxfail 0
debug
kdebug 4
peers - gprs
#this file contains all the parameters pppd will pass to the modem to establish the GPRS connection
#
# The user and password has been commented out becasue the "noauth" command is being used
#user web
#password web
#
# This places a default route in the routing table with the peer as the gateway
defaultroute
#
# This can also be used to replace existing default routes
#replacedefaultroute
#
# Serial Modem to use
/dev/ttyUSB0
115200
#
# Call this chat script to issue the modem commands
connect "/sbin/chat -v -f /var/etc/ppp/chats/gprs.chat"
#
# Enable debugging to /var/log/messages
debug
#
# Enable kernel debugging level 4
kdebug 4
#
#
ipcp-no-addresses
#
#
noipdefault
#
# Do not require the peer to use authentication
noauth
#
# Disable Van Jacobson style TCP/IP header compression in both TX and RX
novj
#
# Disable compression control protocol,if peer doesnt accept requests for CCP from pppd
noccp
#
# Use RTS/CTS hardware flow control
crtscts
#
# I cant find what this means, but if its not included there is no output to the command prompt
modem -detach
#
# Use DNS given to peer and rewrite /etc/resolv.conf
usepeerdns
#
# pppd will accept the peers idea of its remote ip address
ipcp-accept-remote
#
# pppd will accept the peers idea of its local ip address
ipcp-accept-local
#
