привет всем.устанавливаю PGI 1.0 на sda4.стартую после перезагрузки кнопка6.начинает загружаться и ,,эпик файл,,.
стоит PGI 0.7. подскажите где туплю.IPbox 9000.спасибо.лог сом порта
eth0 - (dev. name: stmmaceth - id: 0, IRQ #133
IO base addr: 0xb8110000)
STMMAC MII Bus: probed
eth0: PHY ID 00008201 at 1 IRQ -1 (0:01) active
RTL8201: Registered new driver
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
NET: Registered protocol family 24
scsi0 : sata_stm
ata1: SATA max UDMA/133 cmd 0xb9209000 ctl 0xb9209820 bmdma 0x00000000 irq 170
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-6: ST380817AS, 3.42, max UDMA/133
ata1.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST380817AS 3.42 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
physmap platform flash device: 02000000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Using physmap partition information
Creating 9 MTD partitions on "physmap-flash":
0x00000000-0x00040000 : "nor.boot"
0x00040000-0x00060000 : "nor.config"
0x00060000-0x00260000 : "nor.kernel"
0x00260000-0x01200000 : "nor.root"
0x01200000-0x02000000 : "nor.db"
0x00060000-0x01200000 : "nor.kernel_root"
0x00060000-0x02000000 : "nor.kernel_root_db"
0x00040000-0x02000000 : "nor.all_noboot"
0x00000000-0x02000000 : "nor.all"
stm-ehci stm-ehci.0: st-ehci
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0x191ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: stm-ohci
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0x191ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
i2c_st40_pio: ST40 PIO based I2C Driver
i2c_st40_pio: allocated pin (2,0) for scl (0x84aa7ca4)
i2c_st40_pio: allocated pin (2,1) for sda (0x84aa7cc0)
i2c_st40_pio: allocated pin (3,0) for scl (0x84aa7db8)
i2c_st40_pio: allocated pin (3,2) for sda (0x84aa7df0)
i2c_st40_pio: allocated pin (4,0) for scl (0x84aa7ecc)
i2c_st40_pio: allocated pin (4,1) for sda (0x84aa7ee8)
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xb0000000 size 0x00400000
cop. addr 0x10000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xb0400000 size 0x00400000
cop. addr 0x10400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
stm_rng hardware driver 1.0 configured
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ip_tables: © 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright © 2004-2005 Intel Corporation <
[email protected]>
IP-Config: Complete:
device=eth0, addr=192.168.1.8, mask=255.255.255.0, gw=192.168.1.1,
host=192.168.1.8, domain=, nis-domain=(none),
bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Waiting 10sec before mounting root device...
PHY: 0:01 - Link is Up - 100/Full
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 100k freed
Warning: unable to open an initial console.
Failed to execute /bin/devinit. Attempting defaults...
INIT: version 2.86 booting
INIT: Entering runlevel: 3
[boot] setting kernel parameters
[boot] mounting /mnt filesystem
[boot] loading PGI settings
[boot] debug is set to [no]
[boot] starting udev
[boot] loading front.ko
[stapi] checking cx firmware presence
[boot] loading ciio.ko
[boot] setting sytem time to micom time
[boot] loading CI kernel module
[db] [18:47:27] started
[db] [18:47:27] running db.dat revision check
[db] [18:47:27] main db.dat rev OK
[db] [18:47:27] pgi extensions rev for db.dat OK
[stapi] starting cx firmware upload
[stapi] init stapi device dir
[stapi] loading stos core
[db] [18:47:28] db.dat has already been checked
[db] [18:47:28] running db.dat integrity check
Load module stos_core [?] by modprobe (pid 360)
Load module stsys_ioctl [252] by modprobe (pid 366)
[stapi] loading a/v companions
[db] [18:47:29] db.dat integrity is ok
[db] [18:47:29] finished
[stapi] inserting multicom
[boot] option dst is [off]
[net] [18:47:29] started
[net] [18:47:29] creating web interface pipe
[net] [18:47:30] init USB comms
[boot] option hdd_check is [off]
[net] [18:47:30] USB_MODEM is not set, will be ignored
[net] [18:47:30] bringing up interface lo
modprobe: can't load module mme_host (extra/mme/mme_host.ko): Operation not permitted
[net] [18:47:31] bringing up interface eth0
udhcpc (v1.18.4) started
Sending discover...
Sending select for 192.168.0.101...
Lease of 192.168.0.101 obtained, lease time 604800
adding dns 192.168.0.1
[boot] checking for missing config files in /var
[net] [18:47:31] PPPD_PEER is not set in pgi.conf, aborting dialup
[net] [18:47:31] setting hostname to [cuberevo]
[net] [18:47:31] starting inetd
[hdd] [18:47:31] started
[main] [18:47:32] started
[net] [18:47:32] network is ready
[hdd] [18:47:32] creating sbox hdd pipe
[net] [18:47:32] NTP sync is disabled, system time = micom time
[hdd] [18:47:32] init block devices
[net] [18:47:32] samba daemon is disabled, skipping
[net] [18:47:32] nfs daemon is disabled, skipping
[net] [18:47:32] sending mount request to sbox automounter
[net] [18:47:32] finished
MAC address handling is off
webtv is disabled
[main] [18:47:33] setting tv mode: [1920x1080-50icvbs]
[main] [18:47:33] user set skin: [default]
[main] [18:47:33] actual skin: [/usr/share/sbox/image/dark]
[main] [18:47:33] EPG_DIR is set to [/media]
[stapi] inserting stapi modules
Load module stevt_core [?] by modprobe (pid 586)
Load module stcommon_core [?] by modprobe (pid 586)
Load module stclkrv_core [?] by modprobe (pid 586)
Load module stfdma_core [251] by modprobe (pid 586)
Load module stmerge_core [?] by modprobe (pid 586)
Load module stavmem_core [?] by modprobe (pid 586)
Load module stbuffer_core [?] by modprobe (pid 586)
Load module stinject_core [?] by modprobe (pid 586)
Load module sti2c_core [?] by modprobe (pid 586)
Load module stpio_core [?] by modprobe (pid 586)
Load module stpwm_core [?] by modprobe (pid 586)
Load module stdenc_core [?] by modprobe (pid 586)
Load module stlayer_core [?] by modprobe (pid 586)
Load module stvout_core [?] by modprobe (pid 586)
Load module stvtg_core [?] by modprobe (pid 586)
Load module stvid_core [?] by modprobe (pid 586)
Load module stvin_core [?] by modprobe (pid 586)
Load module stvmix_core [?] by modprobe (pid 586)
Load module stgxobj_core [?] by modprobe (pid 586)
Load module staudlx_core [250] by modprobe (pid 586)
Load module stblit_core [?] by modprobe (pid 586)
Load module sthdmi_core [?] by modprobe (pid 586)
Load module stpti4_core [?] by modprobe (pid 586)
Load module sttuner_core [249] by modprobe (pid 586)
Load module stevt_ioctl [248] by modprobe (pid 596)
Load module stcommon_ioctl [247] by modprobe (pid 596)
Load module stfdma_ioctl [245] by modprobe (pid 596)
Load module stmerge_ioctl [244] by modprobe (pid 596)
Load module stavmem_ioctl [243] by modprobe (pid 596)
Load module stbuffer_ioctl [242] by modprobe (pid 596)
Load module stinject_ioctl [241] by modprobe (pid 596)
Load module sti2c_ioctl [240] by modprobe (pid 596)
Load module stspi_ioctl [239] by modprobe (pid 596)
Load module stpio_ioctl [238] by modprobe (pid 596)
Load module stpwm_ioctl [237] by modprobe (pid 596)
Load module stdenc_ioctl [236] by modprobe (pid 596)
Load module stlayer_ioctl [235] by modprobe (pid 596)
Load module stvout_ioctl [234] by modprobe (pid 596)
Load module stvtg_ioctl [233] by modprobe (pid 596)
Load module stvid_ioctl [232] by modprobe (pid 596)
Load module stvin_ioctl [230] by modprobe (pid 596)
Load module stvmix_ioctl [229] by modprobe (pid 596)
Load module stgxobj_ioctl [228] by modprobe (pid 596)
Load module stblit_ioctl [226] by modprobe (pid 596)
Load module sthdmi_ioctl [225] by modprobe (pid 596)
Load module stpti4_ioctl [224] by modprobe (pid 596)
Load module sttuner_ioctl [223] by modprobe (pid 596)
[main] [18:47:43] HDD will be initialised in the background
[main] [18:47:43] starting sbox application
compiled at 04/17/11 21:08:19 by bhishma@Waterhouse
ioctl failed.(Invalid argument)
*** Error GRAFIX_Init:196: [TODO] remove text init
*** Error stapi_init:190: [sTAPI_WRAP] AUD_Init() failed
[iNITIALIZER] Failed to initialize "st_init(-1)"
Close
[main] [18:47:45] sbox return value: [255]
INIT: Sending processes the TERM signal
shutting down...
unmounting /mnt/usb/sda3...
remounting root as (ro)...
spinning down HDD...
halting...