seleznyov

только что попробывал подключится к PPPoE из UBUNTU Может это поможет ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr e0:cb:4e:c3:d6:78 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e2cb:4eff:fec3:d678/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4971 errors:0 dropped:0 overruns:0 frame:0 TX packets:127 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:342596 (342.5 KB) TX bytes:12982 (12.9 KB) Interrupt:34 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) ppp0 Link encap:Point-to-Point Protocol inet addr:212.115.234.1 P-t-P:212.115.225.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:44 errors:0 dropped:0 overruns:0 frame:0 TX packets:44 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:6418 (6.4 KB) TX bytes:3112 (3.1 KB)

У меня всё как здесь. Ну тогда я уже не знаю, что и делать. Ну может быть я чтото делаю не так. Почему когда я подключаю PPPoE в DIR-320 с родной прошивкой скорость как была такая она и осталась, а когда с прошивками Олега, DANtes просто *опа. Я роутер для шары покупал. Подскажите что мне еще нужно сделать, пожалуйста.

Подскажите описания всех процессов в прошивке от DANtes, чтобы знать что отключать, а что нет или что нужно оставить чтобы подключиться по кабелю и пользоваться mpcs без модемов.

И еще вопрос Всётаки что должно отображаться в сети. Сейчас на родной прошивке - DIR-320

Ради эксперимента вернул родную прошивку. Все работает идеально. Ставлю прошивку либо Олега либо DANtes, получается какаято *ОПА. Щас буду пробовать, чудес на свете не бывает.

Отключил. Изменений нет.

Слава богу с N-го раза DIR-320 подключился по PPPoE (MTU - 1500, по другому никак), но скорость интернета не просто упала, а короче капец. Некоторые сайты просто висят, а некоторые могут загрузиться мгновенно. А ping сервера - сплошные разрывы. Так и должно быть? Торент закачка была 6-7 Мб/с, сейчас в лучшем случае 2 Мб/с и постоянно скачет. Проц роутера грузит на 100% Караул. Помогите

Еще раз прошу помочь подключить DIR-320 PPPoE. Процесс подключения 6 постами выше.

10. NETWORK - MTU - 1500 Save Changes - Apply Changes Указал

Уважаемые пользователи. Подскажите как мне правильно подключить роутер DIR-320 PPPoE. Имею DIR-320, по всем инструкциям сделал com порт, прошил роутер прошивкой DANtes ASUS_WL-500gPv2_WL-520gU_D-Link_DIR-320_linux_2.6.30.10_DANtes У меня кабельный интернет, скорость 100 Мбит, подключение к интернету через PPPoE, т.е. ЛОГИН и ПАРОЛЬ (IP выделенный). Как я пытался подключиться: 1. Прошил роутер 2. После прошивки В сетевой карте TCP/IPv4 - IP получать автоматически. 3. Зашел в броузер 192.168.1.1. 4. Установил пароль 5. Установил Timezone - Save Changes - Apply Changes 6. Отключил ненужные Services - Reboot 7. Воткнул сетевой кабель 8. Зашел в NETWORK Network Configuration lan Configuration - Connection Type - Static IP - Type - Bridge - MAC - - IP Address - 192.168.1.1 - Netmask - 255.255.255.0 - Default Gateway - wan Configuration - Connection Type - PPPOE - Type - None - MAC - - Username - ЛОГИН - Password - ПАРОЛЬ - MTU - 1400 - Default Route - галочка Save Changes - Apply Changes 9.пункт STATUS - PPPoE Syslog: pppd (Last 500 lines) Jan 1 02:19:59 OpenWrt daemon.notice pppd[2553]: secondary DNS address 212.115.255.5 Jan 1 02:19:59 OpenWrt daemon.notice pppd[2553]: remote IP address 212.115.225.2 Jan 1 02:19:59 OpenWrt daemon.notice pppd[2553]: primary DNS address 212.115.255.55 Jan 1 02:19:59 OpenWrt daemon.notice pppd[2553]: peer from calling number 00:24:3F:6A:88:82 authorized Jan 1 02:19:59 OpenWrt daemon.notice pppd[2553]: local IP address 212.115.234.1 Jan 1 02:19:59 OpenWrt daemon.notice pppd[2553]: CHAP authentication succeeded Jan 1 02:19:49 OpenWrt daemon.notice pppd[2553]: Connect: ppp0 <--> eth0.1 Jan 1 02:19:49 OpenWrt daemon.info pppd[2553]: Using interface ppp0 Jan 1 02:19:49 OpenWrt daemon.info pppd[2553]: PPP session is 35612 Jan 1 02:19:49 OpenWrt daemon.err pppd[2553]: Interface eth0.1 has MTU of 1400 -- should be 1500. You may have serious connection problems. Jan 1 02:19:18 OpenWrt daemon.warn pppd[2553]: LCP: timeout sending Config-Requests Jan 1 02:19:18 OpenWrt daemon.notice pppd[2553]: Modem hangup Jan 1 02:19:18 OpenWrt daemon.notice pppd[2553]: Connection terminated. Jan 1 02:18:27 OpenWrt daemon.notice pppd[2553]: Connect: ppp0 <--> eth0.1 Jan 1 02:18:27 OpenWrt daemon.info pppd[2553]: Using interface ppp0 Jan 1 02:18:27 OpenWrt daemon.info pppd[2553]: PPP session is 35543 Jan 1 02:18:27 OpenWrt daemon.err pppd[2553]: Interface eth0.1 has MTU of 1400 -- should be 1500. You may have serious connection problems. Jan 1 02:17:57 OpenWrt daemon.warn pppd[2553]: LCP: timeout sending Config-Requests Jan 1 02:17:57 OpenWrt daemon.notice pppd[2553]: Modem hangup Jan 1 02:17:57 OpenWrt daemon.notice pppd[2553]: Connection terminated. Jan 1 02:17:06 OpenWrt daemon.notice pppd[2553]: pppd 2.4.4 started by root, uid 0 Jan 1 02:17:06 OpenWrt daemon.notice pppd[2553]: Connect: ppp0 <--> eth0.1 Jan 1 02:17:06 OpenWrt daemon.info pppd[2553]: Using interface ppp0 Jan 1 02:17:06 OpenWrt daemon.info pppd[2553]: PPP session is 35467 Jan 1 02:17:06 OpenWrt daemon.info pppd[2526]: Plugin rp-pppoe.so loaded. Jan 1 02:17:06 OpenWrt daemon.err pppd[2553]: Interface eth0.1 has MTU of 1400 -- should be 1500. You may have serious connection problems. 10. NETWORK - MTU - 1500 Save Changes - Apply Changes 11. System - Reboot 12. PPPoE Status Reconnect wan Reconnect wan1 Manual Control: Disconnect wan Disconnect wan1 Connect wan Connect wan1 Ip Addr: Ifconfig ppp0 Syslog: pppd (Last 500 lines) Jan 1 00:00:23 OpenWrt daemon.notice pppd[473]: pppd 2.4.4 started by root, uid 0 Jan 1 00:00:22 OpenWrt daemon.info pppd[461]: Plugin rp-pppoe.so loaded. 13. LOG Jan 1 00:00:13 OpenWrt user.info kernel: Calibrating delay loop... 239.61 BogoMIPS (lpj=479232) Jan 1 00:00:13 OpenWrt user.warn kernel: Mount-cache hash table entries: 512 Jan 1 00:00:13 OpenWrt user.info kernel: net_namespace: 532 bytes Jan 1 00:00:13 OpenWrt user.info kernel: NET: Registered protocol family 16 Jan 1 00:00:13 OpenWrt user.warn kernel: bio: create slab <bio-0> at 0 Jan 1 00:00:13 OpenWrt user.debug kernel: Switched to high resolution mode on CPU 0 Jan 1 00:00:13 OpenWrt user.info kernel: NET: Registered protocol family 2 Jan 1 00:00:13 OpenWrt user.info kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Jan 1 00:00:13 OpenWrt user.info kernel: TCP established hash table entries: 1024 (order: 1, 8192 bytes) Jan 1 00:00:13 OpenWrt user.info kernel: TCP bind hash table entries: 1024 (order: 0, 4096 bytes) Jan 1 00:00:13 OpenWrt user.info kernel: TCP: Hash tables configured (established 1024 bind 1024) Jan 1 00:00:13 OpenWrt user.info kernel: TCP reno registered Jan 1 00:00:13 OpenWrt user.info kernel: NET: Registered protocol family 1 Jan 1 00:00:13 OpenWrt user.info kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher Jan 1 00:00:13 OpenWrt user.warn kernel: Registering mini_fo version $Id$ Jan 1 00:00:13 OpenWrt user.info kernel: JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. Jan 1 00:00:13 OpenWrt user.info kernel: msgmni has been set to 57 Jan 1 00:00:13 OpenWrt user.info kernel: alg: No test for stdrng (krng) Jan 1 00:00:13 OpenWrt user.info kernel: io scheduler noop registered Jan 1 00:00:13 OpenWrt user.info kernel: io scheduler deadline registered (default) Jan 1 00:00:13 OpenWrt user.info kernel: Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled Jan 1 00:00:13 OpenWrt user.info kernel: serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A Jan 1 00:00:13 OpenWrt user.info kernel: serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A Jan 1 00:00:13 OpenWrt user.info kernel: serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A Jan 1 00:00:13 OpenWrt user.info kernel: serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A Jan 1 00:00:13 OpenWrt user.info kernel: b44.c:v2.0 Jan 1 00:00:13 OpenWrt user.info kernel: eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:90:4c:c0:00:00 Jan 1 00:00:13 OpenWrt user.warn kernel: flash init: 0x1c000000 0x02000000 Jan 1 00:00:13 OpenWrt user.info kernel: Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank Jan 1 00:00:13 OpenWrt user.debug kernel: Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0 Jan 1 00:00:13 OpenWrt user.debug kernel: Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0 Jan 1 00:00:13 OpenWrt user.debug kernel: Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0 Jan 1 00:00:13 OpenWrt user.debug kernel: Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0 Jan 1 00:00:13 OpenWrt user.debug kernel: Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0 Jan 1 00:00:13 OpenWrt user.debug kernel: Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0 Jan 1 00:00:13 OpenWrt user.debug kernel: Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0 Jan 1 00:00:13 OpenWrt user.warn kernel: Amd/Fujitsu Extended Query Table at 0x0040 Jan 1 00:00:13 OpenWrt user.warn kernel: Physically mapped flash: Swapping erase regions for broken CFI table. Jan 1 00:00:13 OpenWrt user.notice kernel: number of CFI chips: 1 Jan 1 00:00:13 OpenWrt user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Jan 1 00:00:13 OpenWrt user.notice kernel: Flash device: 0x400000 at 0x1fc00000 Jan 1 00:00:13 OpenWrt user.notice kernel: bootloader size: 262144 Jan 1 00:00:13 OpenWrt user.notice kernel: Creating 4 MTD partitions on "Physically mapped flash": Jan 1 00:00:13 OpenWrt user.notice kernel: 0x000000000000-0x000000040000 : "cfe" Jan 1 00:00:13 OpenWrt user.notice kernel: 0x000000040000-0x0000003f0000 : "linux" Jan 1 00:00:13 OpenWrt user.notice kernel: 0x000000113000-0x0000003f0000 : "rootfs" Jan 1 00:00:13 OpenWrt user.warn kernel: mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only Jan 1 00:00:13 OpenWrt user.notice kernel: mtd: partition "rootfs" set to be root filesystem Jan 1 00:00:13 OpenWrt user.info kernel: mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=50000 Jan 1 00:00:13 OpenWrt user.notice kernel: 0x0000003a0000-0x0000003f0000 : "rootfs_data" Jan 1 00:00:13 OpenWrt user.notice kernel: 0x0000003f0000-0x000000400000 : "nvram" Jan 1 00:00:13 OpenWrt user.info kernel: BCM47xx Watchdog Timer enabled (30 seconds, nowayout) Jan 1 00:00:13 OpenWrt user.info kernel: TCP westwood registered Jan 1 00:00:13 OpenWrt user.info kernel: NET: Registered protocol family 17 Jan 1 00:00:13 OpenWrt user.info kernel: 802.1Q VLAN Support v1.8 Ben Greear <[email protected]> Jan 1 00:00:13 OpenWrt user.info kernel: All bugs added by David S. Miller <[email protected]> Jan 1 00:00:13 OpenWrt user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Jan 1 00:00:13 OpenWrt user.info kernel: Freeing unused kernel memory: 128k freed Jan 1 00:00:13 OpenWrt user.warn kernel: Please be patient, while OpenWrt loads ... Jan 1 00:00:13 OpenWrt user.warn kernel: diag: Detected 'D-Link DIR-320' Jan 1 00:00:13 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex. Jan 1 00:00:13 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX. Jan 1 00:00:13 OpenWrt user.info kernel: roboswitch: Probing device eth0: found a 5325! It's a 5350. Jan 1 00:00:13 OpenWrt user.info kernel: b44: eth0: powering down PHY Jan 1 00:00:13 OpenWrt user.info kernel: mini_fo: using base directory: / Jan 1 00:00:13 OpenWrt user.info kernel: mini_fo: using storage directory: /jffs Jan 1 00:00:16 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex. Jan 1 00:00:16 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX. Jan 1 00:00:17 OpenWrt user.info kernel: device eth0.0 entered promiscuous mode Jan 1 00:00:17 OpenWrt user.info kernel: device eth0 entered promiscuous mode Jan 1 00:00:17 OpenWrt user.info kernel: br-lan: port 1(eth0.0) entering forwarding state Jan 1 00:00:20 OpenWrt user.info kernel: PPP generic driver version 2.4.2 Jan 1 00:00:20 OpenWrt user.info kernel: HDLC line discipline: version $Revision: 4.8 $, maxframe=4096 Jan 1 00:00:20 OpenWrt user.info kernel: N_HDLC line discipline registered. Jan 1 00:00:20 OpenWrt user.info kernel: NET: Registered protocol family 24 Jan 1 00:00:21 OpenWrt user.info kernel: cfg80211: Using static regulatory domain info Jan 1 00:00:21 OpenWrt user.info kernel: cfg80211: Regulatory domain: US Jan 1 00:00:21 OpenWrt user.info kernel: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Jan 1 00:00:21 OpenWrt user.info kernel: (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) Jan 1 00:00:21 OpenWrt user.info kernel: (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Jan 1 00:00:21 OpenWrt user.info kernel: (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Jan 1 00:00:21 OpenWrt user.info kernel: (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Jan 1 00:00:21 OpenWrt user.info kernel: (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Jan 1 00:00:21 OpenWrt user.info kernel: (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) Jan 1 00:00:21 OpenWrt user.info kernel: cfg80211: Calling CRDA for country: US Jan 1 00:00:22 OpenWrt daemon.info pppd[461]: Plugin rp-pppoe.so loaded. Jan 1 00:00:23 OpenWrt user.notice kernel: SCSI subsystem initialized Jan 1 00:00:23 OpenWrt daemon.notice pppd[473]: pppd 2.4.4 started by root, uid 0 Jan 1 00:00:24 OpenWrt user.info kernel: usbcore: registered new interface driver usbfs Jan 1 00:00:24 OpenWrt user.info kernel: usbcore: registered new interface driver hub Jan 1 00:00:24 OpenWrt user.info kernel: usbcore: registered new device driver usb Jan 1 00:00:26 OpenWrt user.info kernel: b43-phy0: Broadcom 5354 WLAN found (core revision 13) Jan 1 00:00:26 OpenWrt user.debug kernel: phy0: Selected rate control algorithm 'minstrel' Jan 1 00:00:26 OpenWrt user.info kernel: Registered led device: b43-phy0::tx Jan 1 00:00:26 OpenWrt user.info kernel: Registered led device: b43-phy0::rx Jan 1 00:00:26 OpenWrt user.info kernel: Registered led device: b43-phy0::radio Jan 1 00:00:26 OpenWrt user.info kernel: Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ] Jan 1 00:00:27 OpenWrt user.info kernel: cfg80211: Regulatory domain changed to country: US Jan 1 00:00:27 OpenWrt user.info kernel: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Jan 1 00:00:27 OpenWrt user.info kernel: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) Jan 1 00:00:27 OpenWrt user.info kernel: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) Jan 1 00:00:27 OpenWrt user.info kernel: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Jan 1 00:00:27 OpenWrt user.info kernel: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Jan 1 00:00:27 OpenWrt user.info kernel: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Jan 1 00:00:27 OpenWrt user.info kernel: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) Jan 1 00:00:30 OpenWrt user.info kernel: tun: Universal TUN/TAP device driver, 1.6 Jan 1 00:00:30 OpenWrt user.info kernel: tun: © 1999-2004 Max Krasnyansky <[email protected]> Jan 1 00:00:30 OpenWrt user.info kernel: PPP MPPE Compression module registered Jan 1 00:00:31 OpenWrt user.info kernel: ip_tables: © 2000-2006 Netfilter Core Team Jan 1 00:00:31 OpenWrt user.warn kernel: Driver 'sd' needs updating - please use bus_type methods Jan 1 00:00:32 OpenWrt user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Jan 1 00:00:32 OpenWrt user.info kernel: PPTP driver version 0.8.4 Jan 1 00:00:32 OpenWrt user.warn kernel: nf_conntrack version 0.5.0 (512 buckets, 2048 max) Jan 1 00:00:34 OpenWrt user.warn kernel: nf_conntrack_rtsp v0.6.21 loading Jan 1 00:00:34 OpenWrt user.warn kernel: nf_nat_rtsp v0.6.21 loading Jan 1 00:00:34 OpenWrt user.info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Jan 1 00:00:34 OpenWrt user.info kernel: ohci_hcd ssb0:1: SSB OHCI Controller Jan 1 00:00:34 OpenWrt user.info kernel: ohci_hcd ssb0:1: new USB bus registered, assigned bus number 1 Jan 1 00:00:34 OpenWrt user.info kernel: ohci_hcd ssb0:1: irq 6, io mem 0x18003000 Jan 1 00:00:34 OpenWrt user.info kernel: usb usb1: configuration #1 chosen from 1 choice Jan 1 00:00:34 OpenWrt user.info kernel: hub 1-0:1.0: USB hub found Jan 1 00:00:34 OpenWrt user.info kernel: hub 1-0:1.0: 2 ports detected Jan 1 00:00:34 OpenWrt user.info kernel: ohci_hcd ssb0:1: SSB EHCI Controller Jan 1 00:00:34 OpenWrt user.info kernel: ohci_hcd ssb0:1: new USB bus registered, assigned bus number 2 Jan 1 00:00:34 OpenWrt user.info kernel: ohci_hcd ssb0:1: irq 6, io mem 0x18003800 Jan 1 00:00:34 OpenWrt user.info kernel: ohci_hcd ssb0:1: USB 0.0 started, EHCI 1.00 Jan 1 00:00:34 OpenWrt user.info kernel: usb usb2: configuration #1 chosen from 1 choice Jan 1 00:00:34 OpenWrt user.info kernel: hub 2-0:1.0: USB hub found Jan 1 00:00:34 OpenWrt user.info kernel: hub 2-0:1.0: 2 ports detected Jan 1 00:00:35 OpenWrt user.info kernel: usbcore: registered new interface driver cdc_acm Jan 1 00:00:35 OpenWrt user.info kernel: cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters Jan 1 00:00:35 OpenWrt user.info kernel: usbcore: registered new interface driver usblp Jan 1 00:00:36 OpenWrt user.info kernel: hso: drivers/net/usb/hso.c: 1.2 Option Wireless Jan 1 00:00:36 OpenWrt user.info kernel: usbcore: registered new interface driver hso Jan 1 02:00:40 OpenWrt user.info kernel: b43 ssb0:3: firmware: requesting b43/ucode13.fw Jan 1 02:00:41 OpenWrt user.info kernel: b43 ssb0:3: firmware: requesting b43/lp0initvals13.fw Jan 1 02:00:41 OpenWrt user.info kernel: b43 ssb0:3: firmware: requesting b43/lp0bsinitvals13.fw Jan 1 02:00:41 OpenWrt user.info kernel: b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10) Jan 1 02:00:47 OpenWrt user.info kernel: device wlan0 entered promiscuous mode Jan 1 02:00:47 OpenWrt user.info kernel: br-lan: port 2(wlan0) entering forwarding state Jan 1 02:00:49 OpenWrt user.info kernel: device wlan0 left promiscuous mode Jan 1 02:00:49 OpenWrt user.info kernel: br-lan: port 2(wlan0) entering disabled state Jan 1 02:00:49 OpenWrt user.info kernel: device wlan0 entered promiscuous mode Jan 1 02:00:49 OpenWrt user.info kernel: br-lan: port 2(wlan0) entering forwarding state Jan 1 02:00:50 OpenWrt user.info sysinit: Loading defaults Jan 1 02:00:51 OpenWrt user.info sysinit: Loading synflood protection Jan 1 02:00:51 OpenWrt user.info sysinit: Adding custom chains Jan 1 02:00:52 OpenWrt user.info sysinit: Loading zones Jan 1 02:00:54 OpenWrt user.info sysinit: Loading forwarding Jan 1 02:00:54 OpenWrt user.info sysinit: Loading redirects Jan 1 02:00:54 OpenWrt user.info sysinit: Loading rules Jan 1 02:00:54 OpenWrt user.info sysinit: Loading includes Jan 1 02:00:54 OpenWrt user.info sysinit: Loading zone defaults Jan 1 02:00:55 OpenWrt user.notice root: adding lan (br-lan) to firewall zone lan Jan 1 02:00:56 OpenWrt authpriv.info dropbear[1164]: Running in background Jan 1 02:00:57 OpenWrt user.info sysinit: pppoe: ioctl(SIOCGIFHWADDR): No such device Jan 1 02:00:57 OpenWrt daemon.err pppoe-relay[1171]: ioctl(SIOCGIFHWADDR): No such device Jan 1 02:01:01 OpenWrt daemon.info dnsmasq[1195]: started, version 2.51 cachesize 150 Jan 1 02:01:01 OpenWrt daemon.info dnsmasq[1195]: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP Jan 1 02:01:01 OpenWrt daemon.info dnsmasq-dhcp[1195]: DHCP, IP range 192.168.1.100 -- 192.168.1.251, lease time 12h Jan 1 02:01:01 OpenWrt daemon.info dnsmasq[1195]: using local addresses only for domain lan Jan 1 02:01:01 OpenWrt daemon.warn dnsmasq[1195]: no servers found in /tmp/resolv.conf.auto, will retry Jan 1 02:01:01 OpenWrt daemon.info dnsmasq[1195]: read /etc/hosts - 1 addresses Jan 1 02:01:01 OpenWrt daemon.err dnsmasq-dhcp[1195]: failed to read /etc/ethers: No such file or directory Jan 1 02:01:08 OpenWrt daemon.warn dnsmasq-dhcp[1195]: DHCP packet received on eth0.1 which has no address Jan 1 02:01:23 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:01:26 OpenWrt daemon.warn dnsmasq-dhcp[1195]: DHCP packet received on eth0.1 which has no address Jan 1 02:01:26 OpenWrt daemon.warn dnsmasq-dhcp[1195]: DHCP packet received on eth0.1 which has no address Jan 1 02:01:26 OpenWrt daemon.warn dnsmasq-dhcp[1195]: DHCP packet received on eth0.1 which has no address Jan 1 02:01:34 OpenWrt daemon.warn dnsmasq-dhcp[1195]: DHCP packet received on eth0.1 which has no address Jan 1 02:01:39 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:01:54 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:02:09 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:02:21 OpenWrt daemon.warn dnsmasq-dhcp[1195]: DHCP packet received on eth0.1 which has no address Jan 1 02:02:24 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:02:39 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:02:54 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:03:09 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:03:24 OpenWrt user.info sysinit: ping: sendto: Network is unreachable Jan 1 02:03:39 OpenWrt user.info sysinit: ping: sendto: Network is unreachable ЧТО Я ДЕЛАЮ НЕ ТАК. И еще вопрос, когда роутер был с родной прошивкой, в сети Windows 7 его видел как DIR-320, когда я его прошивал прошивкой Олега в сети Windows 7 его видел как ASUS, а с прошивками DANtes - его вообще нет. Надеюсь на помощь. Заранее благодарю.

Подскажите пожалуйста как прошить DIR-320 прошивкой от DANtes на прошивку от Олега.

Подскажите пожалуйста. Имеется кабельный интернет, подключение к интернету через PPPoE, ресивер openbox 730. Какое необходимо оборудование для шаринга без компьютера.

Подскажите, как в Ubuntu запустить mpcs при включении, как отдельную службу.