kyk

U-Boot 1.3.1 (Oct 24 2008 - 18:17:25) - stm23-2008-03-19
Board: cuberevo-mini II (0x2D42C041)
Board: 14 dotmatrix vfd front
DRAM:  128 MB
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Reserve 0x2010000 bytes from 0xa5ff0000 for DGS upgrade buffer.
Saving Environment to Flash...
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
Protected 1 sectors

Reset IDE: Bus 0: OK
  Device 0: Model: FUJITSU MHY2200BH  Firm: 0000000B Ser#: 4KQ27T2B36P1
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 190782.2 MB = 186.3 GB (390721968 x 512)

2176747 bytes read
## Booting image at a5ff0000 ...
   Image Name:   Linux-2.6.32.71_stm24_0217
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    2176683 Bytes =  2.1 MB
   Load Address: 84001000
   Entry Point:  84002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Warning: Unable to determine if kernel is built for 29- or 32-bit mode!

Starting kernel console=ttyAS1,115200 panic=3 root=/dev/sda3 rw rootdelay=10 init=/bin/devinit ip=192.168.1.8:192.168.1.1:192.168.1.1:255.255.255.0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 - 0x00000000 - 0 ...

Linux version 2.6.32.71_stm24_0217 (@Fedora) (gcc version 4.9.4 (GCC) ) #2 PREEMPT Thu Feb 14 18:10:06 CET 2019
Boot params:
... MOUNT_ROOT_RDONLY - 88802690
... RAMDISK_FLAGS     - 8920169a
... ORIG_ROOT_DEV     - 8794001a
... LOADER_TYPE       - 00000000
... INITRD_START      - 00000000
... INITRD_SIZE       - 00000000
Booting machvec: STb7100 Reference board
Node 0: start_pfn = 0x4000, low = 0xc000
Zone PFN ranges:
  Normal   0x00004000 -> 0x0000c000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00004000 -> 0x0000c000
STMicroelectronics STb7100 Reference board initialisation
STx7109 version 3.x
Chip version 3.2
bpa2: partition 'LMI_VID' created at 0x10800000, size 57344 kB (0x03800000 B)
bpa2: partition 'LMI_SYS' created at 0x044ad000, size 19456 kB (0x01300000 B)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyAS1,115200 panic=3 root=/dev/sda3 rw rootdelay=10 init=/bin/devinit ip=192.168.1.8:192.168.1.1:192.168.1.1:255.255.255.0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
PVR=04061100 CVR=30480000 PRR=00009300
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 106580k/131072k available (2733k kernel code, 777k data, 124k init)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:600
console [ttyAS1] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
Mount-cache hash table entries: 512
CPU: STx7109
devtmpfs: initialized
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
sq: Registering store queue API.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Slow work thread pool: Starting up
Slow work thread pool: Ready
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
JFS: nTxBlock = 833, nTxLock = 6670
msgmni has been set to 208
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0x18032000 (irq = 121) is a stm-asc
stm-asc.1: ttyAS1 at MMIO 0x18033000 (irq = 120) is a stm-asc
MiPHY driver style MiPHY-DUMMY probed successfully
MiPHY-DUMMY, c0.0 Claimed by sata-stm
scsi0 : sata-stm
ata1: SATA max UDMA/133 irq 170
physmap platform flash device: 02000000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 9 MTD partitions on "physmap-flash":
0x000000000000-0x000000040000 : "nor.boot"
0x000000040000-0x000000060000 : "nor.config_welcome"
0x000000060000-0x000000280000 : "nor.kernel"
0x000000280000-0x000001600000 : "nor.root"
0x000001600000-0x000002000000 : "nor.var"
0x000000060000-0x000001600000 : "nor.mtd2_mtd3"
0x000000060000-0x000002000000 : "nor.mtd2_mtd3_mtd4"
0x000000040000-0x000002000000 : "nor.full"
0x000000000000-0x000002000000 : "nor.all"
        DWMAC100
 No HW DMA feature register supported
 Normal descriptors
STMMAC MII Bus: probed
eth0: PHY ID 00008201 at 1 IRQ POLL (0:01) active
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm_usb_probe: usb_48_clk clock not found for stm-usb.0
stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0x191ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0x191ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
i2c_st40_pio: ST40 PIO based I2C Driver for STM24
Linux video capture interface: v2.00
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xb0000000  size      0x00400000
                  cop. addr 0x10000000
    Channels : Not defined
    IRQ      : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xb0400000  size      0x00400000
                  cop. addr 0x10400000
    Channels : Not defined
    IRQ      : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac handler (16 channels).
IRQ 140/fdma_dmac: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma: firmware: using built-in firmware fdma_STx7109_0.elf
platform fdma_dmac: SLIM hw 0.0, FDMA fw 4.6
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
  #0: STMicroelectronics STx7109 cut 3.2 SOC audio subsystem
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F0300)
ata1.00: ATA-8: FUJITSU MHY2200BH, 0000000B, max UDMA/100
ata1.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: restricting to 256 max sectors
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHY2200B 0000 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
        HW MAC address from bdinfo: 00:13:18:02:7d:b7
eth0: device MAC address 00:13:18:02:7d:b7
rtl8201_config_init>
 No MAC Management Counters available
sd 0:0:0:0: [sda] Attached SCSI disk
IP-Config: Complete:
     device=eth0, addr=192.168.1.8, mask=255.255.255.0, gw=192.168.1.1,
     host=192.168.1.8, domain=, nis-domain=(none),
     bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
Waiting 10sec before mounting root device...
PHY: 0:01 - Link is Up - 100/Full
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 8:3.
devtmpfs: mounted
Freeing unused kernel memory: 124k freed
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x10400000
INIT: version 2.88 booting
lircd.conf missing!
Fuse filesystem already available.
Mounting fuse control filesystem.
sh: sda1: unknown operand
Adding 1004020k swap on /dev/sda1.  Priority:-1 extents:1 across:1004020k
EXT4-fs (sda2): warning: mounting unchecked fs, running e2fsck is recommended
EXT4-fs (sda2): mounted filesystem without journal
[micom] micom_init_module >
Cuberevo MINI2 VFD initializing (V1.07)
[micom] myTime= 00.04.2008
[micom] micomGetMicom front_seg_num 14
[micom] micomWriteString >
[micom] micom_init_module <
stmcore-display: STx7109c3 display: probed
device probe found 2 display pipelines
stmfb: fb0 parameters = "1280x720-32@50:16m:pal:cvbs:rgb:yuv"
stmfb: fb1 parameters = "<NULL>"
Init of MME log wrapper
STx71XX MPEG2 hardware host transformer loaded
snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw
pseudocard: 1 pseudo soundcard(s) found
socket_init >
socket_probe >
***************************
socket 1
name socket-1
pio port -1
pio pin -1
active l/h -1
i2c_bus 0
socket_probe <
socket_init < 0
lnbh221_init >
lnbpio_init >
cx24116_init >
cx24116_probe >
found frontend "cx24116" in platform config
cx24116_probe <
cx24116_init < 0
stv090x_init >
stv090x_probe >
found frontend "stv090x" in platform config
stv090x_probe <
stv090x_init < 0
starci2win loaded
pti: module license 'NO' taints kernel.
Disabling lock debugging due to kernel taint
pti loaded (videoMem = 4096, waitMS = 20, enableStatistic = 0)
no swts ->routing streams from dvr0 direct to the player
DVB: registering new adapter (STM Streamer)
0: DeviceContext 8b8ae088, DvbDemux 8b8ae38c, DmxDevice 8b8ae574
membase-0 0xa3000000
membase-1 0xa3010000
ptiInit context = 8b8ae088, demux = 8b8ae38c
[TSM] init stream routing...
Routing streams through cimax
Load real TC Code
TC_Data = b9238000, TC_Code = b923c000
Readback TC ... successfull
using videoMem = 770048 (packets = 4096)
pti: pti_buffer_pool_init: allocate 188 pages (770048 bytes)
DMA(0) base = 5580000, top = 563c000, buffer = 5580000, size 770048
freeBuffer(): free = 1
pti: pti_buffer_pool_init: allocate 188 pages (770048 bytes)
DMA(1) base = 563c000, top = 56f8000, buffer = 563c000, size 770048
freeBuffer(): free = 2
Validity = 0x0001 Mode = 0x0000
pti_task: using 2 dma channel
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
Validity = 0x0001 Mode = 0x0000
Validity = 0x0003 Mode = 0x0000
cx24116_demod_detect > socket-1: i2c-0 addr 0x5
cx24116_demod_detect: Detected cx24116
cx24116_demod_detect <
found cx24116 on socket socket-1
cx24116_demod_attach >
cx24116_register_frontend
fw_name dvb-fe-cx24116.fw
useLNB 2
useUnknwon 1
fw_name dvb-fe-cx24116.fw - dvb-fe-cx24116.fw
lnb_enable_pin 844ac6b0
DVB: registering adapter 0 frontend 0 (Conexant cx24116 DVB-S2)...
cx24116_demod_attach <
Free session: 0
Using session 0
pti_hal_get_new_descrambler (40000) >
pti_hal_get_new_descrambler (40001) >
pti_hal_get_new_descrambler (40002) >
pti_hal_get_new_descrambler (40003) >
pti_hal_get_new_descrambler (40004) >
pti_hal_get_new_descrambler (40005) >
pti_hal_get_new_descrambler (-8) >
pti_hal_get_new_descrambler (-8) >
Descrambler Handler = 40000
1: DeviceContext 8b8ae610, DvbDemux 8b8ae914, DmxDevice 8b8aeafc
ptiInit context = 8b8ae610, demux = 8b8ae914
Free session: 1
Using session 1
pti_hal_get_new_descrambler (41000) >
pti_hal_get_new_descrambler (41001) >
pti_hal_get_new_descrambler (41002) >
pti_hal_get_new_descrambler (41003) >
pti_hal_get_new_descrambler (41004) >
pti_hal_get_new_descrambler (41005) >
pti_hal_get_new_descrambler (-8) >
pti_hal_get_new_descrambler (-8) >
Descrambler Handler = 41000
2: DeviceContext 8b8aeb98, DvbDemux 8b8aee9c, DmxDevice 8b8af084
ptiInit context = 8b8aeb98, demux = 8b8aee9c
convert_source(): invalid frontend source (2)
Free session: 2
Using session 2
pti_hal_get_new_descrambler (42000) >
pti_hal_get_new_descrambler (42001) >
pti_hal_get_new_descrambler (42002) >
pti_hal_get_new_descrambler (42003) >
pti_hal_get_new_descrambler (42004) >
pti_hal_get_new_descrambler (42005) >
pti_hal_get_new_descrambler (-8) >
pti_hal_get_new_descrambler (-8) >
Descrambler Handler = 42000
3: DeviceContext 8b8af120, DvbDemux 8b8af424, DmxDevice 8b8af60c
ptiInit context = 8b8af120, demux = 8b8af424
convert_source(): invalid frontend source (3)
pti_hal_get_new_descrambler (-2) >
pti_hal_get_new_descrambler (-2) >
pti_hal_get_new_descrambler (-2) >
pti_hal_get_new_descrambler (-2) >
pti_hal_get_new_descrambler (-2) >
pti_hal_get_new_descrambler (-2) >
pti_hal_get_new_descrambler (-2) >
pti_hal_get_new_descrambler (-2) >
Descrambler Handler = -2
stm_v4l2_register_driver: driver 'Linux DVB Overlay' registered
OSDEV_LinkDevice - /dev/allocator, Major 245, Minor 0
AllocatorLoadModule : Allocator device loaded
Switching Preprocessor clock to full speed.
Platform STx7109 - cut 3
OSDEV_LinkDevice - /dev/h264pp, Major 246, Minor 0
H264ppLoadModule : H264pp device loaded
[simu_button] initializing ...
[simu_button] allocating and registering button device
input: TDT RC event driver as /devices/virtual/input/input0
zram: Creating 1 devices ...
Setting up swapspace version 1, size = 16773120 bytes
UUID=37e26562-49ea-4445-850b-1f770836a5d7
ALSA: Restoring mixer settings...
rm: can't remove '/dev/rc': No such file or directory
No state is present for card STx7109
Found hardware: "STx7109" "" "" "" ""
Hardware is initialized using a generic method
[evremote2] Model: 'cuberevo-mini2'
[evremote2] vBoxType: 12 (cuberevo-mini2)
[evremote2] Input device name: "TDT RC event driver"
[evremote2] Remote selected: Cuberevo RemoteControl
[evremote2] RemoteControl Map:
             Keyname  Keyword  KeyCode
--------------------------------------
              KEY_F1  -  00  -   59
              KEY_F2  -  01  -   60
              KEY_F3  -  02  -   61
                INFO  -  03  -  358
               RADIO  -  04  -  385
No state is present for card STx7109
            PREVIOUS  -  05  -  412
                 EPG  -  06  -  365
              RECORD  -  07  -  167
           FAVORITES  -  08  -  364
               MEDIA  -  09  -  226
             STANDBY  -  0A  -  116
              KEY_F5  -  0B  -   63
                MUTE  -  0C  -  113
             ARCHIVE  -  0D  -  361
             0BUTTON  -  10  -   11
             1BUTTON  -  11  -    2
             2BUTTON  -  12  -    3
             3BUTTON  -  13  -    4
             4BUTTON  -  14  -    5
             5BUTTON  -  15  -    6
             6BUTTON  -  16  -    7
             7BUTTON  -  17  -    8
             8BUTTON  -  18  -    9
             9BUTTON  -  19  -   10
                  UP  -  1A  -  103
                DOWN  -  1B  -  108
               RIGHT  -  1C  -  106
                LEFT  -  1D  -  105
              REWIND  -  1E  -  168
                  OK  -  1F  -  352
                PLAY  -  20  -  207
         FASTFORWARD  -  21  -  208
                STOP  -  22  -  128
                SLOW  -  23  -  409
               AGAIN  -  24  -  129
               PAUSE  -  25  -  119
                MENU  -  26  -  139
                EXIT  -  27  -  174
              KEY_F7  -  28  -   65
        KEY_BOOMARKS  -  29  -  156
                 RED  -  2A  -  398
                BLUE  -  2B  -  401
              KEY_F8  -  2C  -   66
               GREEN  -  2D  -  399
              YELLOW  -  2E  -  400
               AUDIO  -  2F  -  392
            SUBTITLE  -  30  -  370
                TEXT  -  31  -  388
           CHANNELUP  -  32  -  402
         CHANNELDOWN  -  33  -  403
            VOLUMEUP  -  34  -  115
          VOLUMEDOWN  -  35  -  114
                 WWW  -  36  -  150
--------------------------------------
[evremote2] Supports Long KeyPress: yes
No state is present for card MIXER0
[evremote2 cuberevo] Period = 10, delay = 120
[evremote2 cuberevo] micom version = 2
[evremote2] Using period = 10 delay = 120
Found hardware: "Pseudo Mixer" "Pseudo Mixer" "" "" ""
Hardware is initialized using a generic method
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.dirty_ratio = 60
No state is present for card MIXER0
Configuring packages on first boot....
 (This may take several minutes. Please do not power off the machine.)
update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing)
 Removing any system startup links for run-postinsts ...
  /etc/rcS.d/S99run-postinsts
INIT: Entering runlevel: 3
Configuring network interfaces... ip: RTNETLINK answers: File exists
udhcpc: option -h NAME is deprecated, use -x hostname:NAME
udhcpc (v1.24.1) started
Sending discover...
Sending select for 192.168.1.4...
Lease of 192.168.1.4 obtained, lease time 86400
/etc/udhcpc.d/50default: Adding DNS 192.168.1.1
ip: SIOCGIFFLAGS: No such device
Starting system message bus: dbus.
Starting Dropbear SSH server: Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQCi/75V8qXMtJXxoreipMzpVMM1QZjnKhK0hPtBcBeReBlfeX8hVewNUIoo8wURGwxJnv4mmrR1CplHVUUZjc30QXHaUNacnK8bO54rbvSVjqQAekaNT3zl0+u887kXd4HB+jOZUbbGGyh0T1EjRvCCTTcmUSkLT9HBbmv2SPkRdw== root@cuberevo_mini2
Fingerprint: md5 c5:90:28:fc:3c:2c:15:0d:58:34:b9:f2:56:ca:00:2b
dropbear.
Starting rpcbind daemon...done.
Mounting remote filesystems...
starting statd: done
Current year: 2000 older than 2018 !
Trying to set correct date/time with a maximum timeout of 5 seconds...
26 Feb 14:11:30 ntpdate[1113]: step time server 91.236.251.62 offset 604505434.652881 sec
starting Busybox Periodic Command Scheduler: crond... done.
crond[1119]: crond (busybox 1.24.1) started, log level 8

* starting UPnP client: djmount... done.
Starting internet superserver: inetd.
Starting minidlna minidlna
[2019/02/26 14:11:31] minidlna.c:612: error: Media directory "/media/hdd/movie/" not accessible [No such file or directory]
done
starting 8 nfsd kernel threads: rpc.nfsd: unable to set any sockets for nfsd
Starting ntpd: done
Starting Samba: smbd nmbd.
Starting syslogd/klogd: done
 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
   ...done.
Starting astra
/dev/dvb/adapter0/video0: Device or resource busy
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[MAIN] executing main
no profile data available
close failed in file object destructor:
IOError: [Errno 5] Input/output error
Stopping minidlna minidlna
stopped process in pidfile '/var/run/minidlna/minidlna.pid' (pid 1143)
done
Killed
/dev/dvb/adapter0/video0: Device or resource busy
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[MAIN] executing main
close failed in file object destructor:
IOError: [Errno 5] Input/output error
Killed
/dev/dvb/adapter0/video0: Device or resource busy
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[MAIN] executing main
close failed in file object destructor:
IOError: [Errno 5] Input/output error
Killed
/dev/dvb/adapter0/video0: Device or resource busy
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[MAIN] executing main
init 4